Oh man, where do I begin. Ok, I just ordered a 10" F/4.8 dob. This will be my second scope, so I don't have much experience. I asked for a 1 1/4" focuser because I haven't decided which 2" focuser I want(FeatherTouch, DX1, DX3, etc.). This week I will finally be able to test out a FeatherTouch. So I figured that after I receive this new dob I would have to do some modifications to it. So here are my questions, and there are many:
1. If I go with the 2" FeatherTouch focuser, is this going to screw up my focal length? Or are 1 1/4" focusers generally the same height as 2" low profile? Am I going to have to move the primary back a little bit away from the secondary? I don't know the height of the 1 1/4" focuser as I haven't received the scope yet.
2. When you are setting the distance from the diagonal to the focal plane, how far out do you rack the focuser? In other words, if I have a FeatherTouch with 2 inches of travel, do I rack it out 1 inch and use that distance? That way I will have one inch of out-focus and one inch of in-focus from the focal plane. Following the same logic, if I had a 2" focuser with 3 inches of travel I would rack it out 1.5" when I go to set the distance. Or is that not correct?
3. Am I doing this correctly? Given these figures: 10" f/4.8 dob with a 12" ID tube, a focuser height of 1.6"(FeatherTouch specs) with 2 inches of travel, and a tube thickness of 1/4", my distance from the diagonal to focal plane should be set at 8.85". 6"(radius of ID of tube) + 1/4"(tube thickness) + 1.6"(focuser height fully racked in) + 1"(middle of travel distance for focuser) = 8.85"
4. I will be using Naglers and Pentax ep's in my scope, as well as a Denk II binoviewer. If I go with the FeatherTouch, which travel length would you recommend? They offer 1.5", 2" and 2.5".
Thanks in advance to anybody who tackles all of these questions.
1. If I go with the 2" FeatherTouch focuser, is this going to screw up my focal length? Or are 1 1/4" focusers generally the same height as 2" low profile? Am I going to have to move the primary back a little bit away from the secondary? I don't know the height of the 1 1/4" focuser as I haven't received the scope yet.
2. When you are setting the distance from the diagonal to the focal plane, how far out do you rack the focuser? In other words, if I have a FeatherTouch with 2 inches of travel, do I rack it out 1 inch and use that distance? That way I will have one inch of out-focus and one inch of in-focus from the focal plane. Following the same logic, if I had a 2" focuser with 3 inches of travel I would rack it out 1.5" when I go to set the distance. Or is that not correct?
3. Am I doing this correctly? Given these figures: 10" f/4.8 dob with a 12" ID tube, a focuser height of 1.6"(FeatherTouch specs) with 2 inches of travel, and a tube thickness of 1/4", my distance from the diagonal to focal plane should be set at 8.85". 6"(radius of ID of tube) + 1/4"(tube thickness) + 1.6"(focuser height fully racked in) + 1"(middle of travel distance for focuser) = 8.85"
4. I will be using Naglers and Pentax ep's in my scope, as well as a Denk II binoviewer. If I go with the FeatherTouch, which travel length would you recommend? They offer 1.5", 2" and 2.5".
Thanks in advance to anybody who tackles all of these questions.